ET 
EN Print fan 50% Tõuseb üles fan st tagumine nurk
Print fan 30% tõusid kõik nurgad üles / Print fan 70% palju juuspeeneid niite
Fan kiirus : esmased kihid 0, edasi 40-70% (sõltuivalt kihi print kiirusest min 5s.)
Teise jahutus vent. paigaldus peaks ühtlustama tulemit det. perimeetris
Cura "Z Seam Alignement" tekitab visuaalse defekti /asen sõlt. ZSA palikust (proovin mudida Outer wall wipe distance)
kui ZSA on random siis üldkvalit. langeb.... parim hetkel siiski "Sharpest corner"
PK ! ½tėOĄ Ą custom_esun_petg_solid_silver_[general]
version = 4
name = ESUN_PETG_Solid_Silver
definition = fdmprinter
[metadata]
type = quality_changes
quality_type = fast
setting_version = 16
[values]
acceleration_enabled = True
adhesion_type = skirt
bridge_settings_enabled = True
jerk_enabled = True
layer_height = 0.2
layer_height_0 = 0.28
material_bed_temperature = 80
material_bed_temperature_layer_0 = 80
speed_slowdown_layers = 4
support_enable = False
support_type = everywhere
PK ! ×y« , custom_extruder_1_#2_esun_petg_solid_silver_[general]
version = 4
name = ESUN_PETG_Solid_Silver
definition = fdmprinter
[metadata]
type = quality_changes
quality_type = fast
intent_category = default
position = 0
setting_version = 16
[values]
brim_outside_only = False
brim_width = 5
cool_fan_enabled = True
cool_fan_full_at_height = 0.6
cool_fan_full_layer = =max(1, int(math.floor((cool_fan_full_at_height - resolveOrValue('layer_height_0')) / resolveOrValue('layer_height')) + 2))
cool_fan_speed = =100.0 if cool_fan_enabled else 0.0
cool_fan_speed_max = 70
cool_fan_speed_min = 40
cool_lift_head = False
cool_min_layer_time = 5
cool_min_layer_time_fan_speed_max = 5
cool_min_speed = 5
infill_before_walls = True
infill_material_flow = 90
infill_pattern = zigzag
infill_sparse_density = 15
initial_layer_line_width_factor = 150
ironing_enabled = False
material_final_print_temperature = 235
material_flow = 90
material_flow_layer_0 = 95
material_initial_print_temperature = 235
material_print_temperature = 235
material_print_temperature_layer_0 = 240
outer_inset_first = True
retract_at_layer_change = True
retraction_amount = 3.5
retraction_extra_prime_amount = 0
retraction_hop = 0
retraction_hop_enabled = False
retraction_hop_only_when_collides = True
retraction_speed = 40
skirt_brim_material_flow = 90
skirt_brim_speed = 20
skirt_line_count = 2
speed_infill = 55
speed_layer_0 = 30
speed_print = 45
speed_print_layer_0 = 10
speed_topbottom = 20
speed_travel = 150
speed_travel_layer_0 = 40
speed_wall_x = 55
support_xy_distance = 0.7
support_z_distance = 0.15
travel_avoid_other_parts = True
travel_avoid_supports = False
travel_compensate_overlapping_walls_enabled = True
z_seam_type = sharpest_corner
PK ! ½tėOĄ Ą € custom_esun_petg_solid_silver_PK ! ×y« , €ü custom_extruder_1_#2_esun_petg_solid_silver_PK ¦ Ī